Company:
Contract Professionals, Inc.
Location: Sterling Heights
Closing Date: 20/10/2024
Hours: Full Time
Type: Permanent
Job Requirements / Description
Position Requirements:
Bachelors degree in Electrical Engineering, Computer Engineering (BSCE), Mechatronics, Robotics or related degree program.
2+ years of relevant experience on up.
Ability to use Engineering Development and Test Tools.
Ability to develop technical solutions to complex problems.
Ability to interact with senior external personnel on tech matters.
Aware of and directs activities towards completion of major program goals.
Ability to travel to supplier and government sites as needed.
Knowledge in many, but not all, of the following areas desired
IPC and MIL standards.
Digital and Analog circuit design.
Gyroscopes, Encoders, and Cameras.
Development of component/subsystem requirements.
Model-based Motion Control.
PWM and PID.
Test Equipment (Power Supplies, Oscilloscopes, Function Generators, DACs)
Power, thermal analysis, timing, biasing, voltage and current control, LED control, data packet deciphering, etc.
Schematic development, component selection, circuit simulation, and PCB layout.
Engineering design, development, and analysis software.
Servo Control experience.
MATLAB Simulink Control experience , MATHCAD, Mentor Graphics Schematic. Capture, CAMView or CAM350.
Microprocessor based products including processors, chipsets, memory and bus. interfaces, networking standards (PCI-xpress, DDR2, DDR3, USB, SATA, DVI, etc...)
Microcontrollers including IDEs, configuration, coding, programming and NXP family of microcontrollers.
Industry interface standards and form factors (VITA42/46, COM Express, ETX, etc.).
Serial Interconnects, USB, CAN, RS422/485, etc.).
Graphics/video interfaces (SDI, DVI, HDMI, RS-170, etc.).
EMI/EMC design practices and standards.
C, C#, VisualStudio Suite.
US CITIZENSHIP REQUIREMENT:
This assignment is a US Government Contract which requires all applicants to be US Citizens.
NO SUBCONTRACT REQUIREMENT:
No third-party applicants will be considered. If you are a third party contracting company, please do not respond to this position.
Bachelors degree in Electrical Engineering, Computer Engineering (BSCE), Mechatronics, Robotics or related degree program.
2+ years of relevant experience on up.
Ability to use Engineering Development and Test Tools.
Ability to develop technical solutions to complex problems.
Ability to interact with senior external personnel on tech matters.
Aware of and directs activities towards completion of major program goals.
Ability to travel to supplier and government sites as needed.
Knowledge in many, but not all, of the following areas desired
IPC and MIL standards.
Digital and Analog circuit design.
Gyroscopes, Encoders, and Cameras.
Development of component/subsystem requirements.
Model-based Motion Control.
PWM and PID.
Test Equipment (Power Supplies, Oscilloscopes, Function Generators, DACs)
Power, thermal analysis, timing, biasing, voltage and current control, LED control, data packet deciphering, etc.
Schematic development, component selection, circuit simulation, and PCB layout.
Engineering design, development, and analysis software.
Servo Control experience.
MATLAB Simulink Control experience , MATHCAD, Mentor Graphics Schematic. Capture, CAMView or CAM350.
Microprocessor based products including processors, chipsets, memory and bus. interfaces, networking standards (PCI-xpress, DDR2, DDR3, USB, SATA, DVI, etc...)
Microcontrollers including IDEs, configuration, coding, programming and NXP family of microcontrollers.
Industry interface standards and form factors (VITA42/46, COM Express, ETX, etc.).
Serial Interconnects, USB, CAN, RS422/485, etc.).
Graphics/video interfaces (SDI, DVI, HDMI, RS-170, etc.).
EMI/EMC design practices and standards.
C, C#, VisualStudio Suite.
US CITIZENSHIP REQUIREMENT:
This assignment is a US Government Contract which requires all applicants to be US Citizens.
NO SUBCONTRACT REQUIREMENT:
No third-party applicants will be considered. If you are a third party contracting company, please do not respond to this position.
Share this job
Useful Links